Clinical laboratory incubators offer temperature ranges and uniformity to meet the needs of most incubator users. Select gravity or mechanical convection incubator, according to your preference.

These lab incubator is compact and economic are perfect for bacterialogical cultures, hematology studies or for drying of stained microscope slides for the clinical or classroom use. Full warranties on our lab Incubators and all other laboratory supplies provide you with complete protection.

Mini Low Cost Lab Incubators

Bench top Laboratory incubators use minimum space, yet provide excellent incubation results.

Aluminum lined chamber provides excellent temperature uniformity.
Type I42300 and I104025 incubators contain removable perforated floor shelf and middle shelf for easy decontamination.
Thermometer port on top of incubator permits temperature monitoring without opening the door.
For convenience, lab incubator includes a 12" (30.5 cm) red, spirt filled thermometer (MEX147,-20° to 110°C), which is accurate to NIST tolerances, three wire cord and a plug.

Low-Temperature/B.O.D. Incubator

B.O.D. Incubator is space-saving low temperature incubator. It is preferred for small volume workloads. Easy-to-clean chamber is fully insulated for efficient temperature transfer, and corrosion-resistant to ensure a long, useful life.

The most reproducible test conditions is ensured by gentle forced air circulation. Chamber air is gently and continuously circulated at a rate that ensures temperature uniformity of all test samples. The 1 Amp interior outlet allows use of stirrers, shakers, roller bottles, or other apparatus.

Microprocessor control.
CFC-free refrigerant.
Digital display of temperature.
Easy keypad set and calibration.
Safety high/low-limit thermostat.
Over/under counter.
Gentle forced air circulation.
Interior electrical outlet.

Low-Temperature Incubator

Low-Temperature Incubator is specifically designed for Biological Oxygen Demand (B.O.D.) determination and other applications requiring large capacities, a broad temperature range, and precise temperature control and uniformity.

Mechanical convection incubator features top-mounted microprocessor controls, push-button programming, output for remote alarm light/horn, rear access port, built-in high/low temperature protection, digital temperature display,fully gasketed door with key lock, and output jacks for datalogging.

Chamber interior is equipped with three 68.6W x 44.5D cm (27 x 171/2") top shelves, three 68.6W x 38.1D cm (27 x 15") bottom shelves, and six 61W x 12.7D cm (24 x 5") door shelves.

Epoxy powder-coated exterior.
Supplied with a standard power cord.
UL listed.

Economy Laboratory Incubators

Economy laboratory incubators is ideal for routine lab incubations of small work loads. Economical, low-watt density strip heaters supply efficient heating.

To minimize heat loss and hold temperature within the chamber uniform to ±0.5° @ 37°C. stainless steel chamber is insulated with 5.1 cm (2") of industrial fiberglass. Temperature range is 5° above ambient to 70°C, regulated by a hydraulic temperature controller. Laboratory incubator door is tightly sealed by a 1.27 cm (1/2") silicone gasket. Glossy white interior for easy contamination detection.

Unit includes pilot light, temperature selection dial, three-prong cord and glass thermometer. Supplied with two shelves which are adjustable at 1.27 cm (1/2") increments.

Operates on 110V or 220V, 50/60Hz.
CSA approved.
UL and CUL listed.
CE marked.
Uniformity of ±0.5°@ 37°C.
Flat perforated stainless steel shelves.

Anaerobic Chambers Laboratory Incubator

Anaerobic Chambers Laboratory Incubator, is preferred for beverage, food, and environmental applications. To maintain temperature it features a unique contact heating system and wrap-around insulation. Tempered safety-glass window is floated, providing a tight seal to the silicone rubber door gasket.

For easy installation and operation the 9.5mm (3/8") vacuum valve and 6.4mm (1/4") vent and gas valve are conveniently located on top of the control panel. Anaerobic chamber features a positive door latch, two fixed aluminum shelves and powder-coat paint exterior. Supplied with three-wire cord/plug and glass thermometer, plus one silica and cartridge of catalyst.

Unique contact heating system.
True vacuum and vent/gas valves.
Removable chamber gasket.
Tempered safety glass window.